ASTM D Air Permeability Testing of Textile Fabrics is a standard test method for measurement of the air permeability of textile fabrics. ASTM D – Tensile, Compressive and Flexural Creep and . ASTM D testing covers the measurement of the air permeability of textile fabrics. This test. ASTM D – Standard Test Method for Air Permeability of Textile Fabrics. 1. Scope This test method covers the measurement of the air permeability of.
|Published (Last):||8 July 2012|
|PDF File Size:||15.32 Mb|
|ePub File Size:||8.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
This test applies to most fabrics, including woven fabrics, nonwoven fabrics, air bag fabrics, astm d737, napped fabrics, knitted fabrics, layered fabrics, and pile fabrics.
At a minimum, the test apparatus must provide a pressure drop of Pa Significance and Use This test method is considered satisfactory for f737 testing of commercial aetm since current estimates of between-laboratory precision are acceptable, and this test method is astm d737 extensively in the trade for acceptance testing.
Ensure specimens are free of folds, creases, or wrinkles. Preparation of Test Apparatus and Calibration 8. The weighted ring is not recommended for lofty or stiff fabric.
ASTM D737 – Air Permeability of Textile Fabrics
In the absence of astm d737 an agreement, take the number of fabric rolls or pieces specified in Table 1. The components of variance for air permeability of asm fabrics expressed as standard deviations were calculated to be the values listed in Table 3.
If a bias is found, asgm its cause must be astm d737 and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration of the known bias. The use of a weighted ring and rubber gaskets on the clamp astm d737 has been found to be helpful.
ASTM D – 18 Standard Test Method for Air Permeability of Textile Fabrics
Air permeability also can be used to provide an indication of the breathability of weather-resistant and rainproof fabrics, or of coated fabrics in general, and to detect changes during the astm d737 process. Four of the eight specimens were tested astm d737 one day, and four astm d737 were tested on a second day. Such yarn extension would open up the fabric, increase the free area, and increase the air permeability.
astm d737 The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. The rate of air flow passing perpendicularly through a known area of fabric is adjusted to obtain a prescribed air pressure differential between the two x737 surfaces.
Fabrics with different astm d737 textures on either side can have a different air permeability depending upon the direction of air flow.
Avoid getting oil, water, grease, and so forth, on the specimens when handling. Air permeability also can be used to provide an indication of the breathability of weather-resistant and rainproof fabrics, or of coated fabrics in general, and to detect changes during the manufacturing process.
Wstm astm d737 sufficient differences related to the fabric astm d737 and structure to warrant listing the components of variance and the critical differences separately.
ASTM D Air Permeability » SGS-IPS Testing
Precision and Bias Note—For air permeability results obtained m ft above sea level, correction factors may be required. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate d7377 results were obtained, and are astm d737 assigned in equal number to each laboratory for astm d737.
Awtm the cutting die or template described in 6. In filtration, for example, efficiency is directly related to air permeability. If bias is found, either its cause must be found and corrected, or future test results for that material astm d737 be adjusted in consideration of the known bias. Since the interlaboratory astm d737 for resin-bonded nonwoven fabric included only qstm laboratories and the spun-bonded and thermal nonwoven fabrics included only four laboratories, estimates of between laboratory precision may be astm d737 underestimated or overestimated to a considerable extent and should axtm used with special caution.
The values stated in inch-pound units astm d737 be approximate. This test method is considered satisfactory for acceptance testing of commercial shipments since current estimates of between-laboratory precision are acceptable, and this test method is used extensively in the trade for acceptance testing. Consider the rolls or pieces of fabric to be the primary sampling units.
Test Method F describes a series of usable clamping adaptions to eliminate edge leakage. The components of variance for air astm d737 expressed as standard deviations were calculated to be the astm d737 listed in Table 3.
Consequently, no multi-fabric comparisons were made. Historical Version astm d737 – view previous versions of standard. The average results from the two d773 should be compared using the appropriate statistical analysis and an acceptable probability level chosen by the two parties before testing is begun.